Magnum 8 on ebay
-
- Posts: 46
- Joined: Sun Mar 25, 2012 6:55 pm
Re: Magnum 8 on ebay
Hi Dan
Glad to hear its going well, I use a fair amount of vinyl on cars for work and unless its completely smooth I wouldnt bother, as the good results are hard on even smooth new car pannels plus the cheap carbon effect ones will be a nightmare! I went for painting but mine wasnt that bad. Id try filling it personally i think.
Hope it goes well
Tom
Glad to hear its going well, I use a fair amount of vinyl on cars for work and unless its completely smooth I wouldnt bother, as the good results are hard on even smooth new car pannels plus the cheap carbon effect ones will be a nightmare! I went for painting but mine wasnt that bad. Id try filling it personally i think.
Hope it goes well
Tom
Re: Magnum 8 on ebay
I'd go the paint route, personally - I think the Carbon effect vinyl would be a short lived amusement, and might prove a veneer removing nightmare when trying to take it off again - it might stick to the plywood better than the ply is stuck to itself.
Rupert
Re: Magnum 8 on ebay
Too pretentious for words... Just paint it. No reason for it to be the same colour!hollandsd wrote: I think one easy option is to cover it with a carbon effect vinyl?
Mind you back in the day there were such things as large holes in foredecks with just vinyl covering to save weight. Not advised!
Re: Magnum 8 on ebay
Fair enough, the hull has now been painted, its looking a little orange peely at the moment but im improving.
Look here:
It still needs more coats to cover everything underneath where the primer got a little thin.
With the spreader arangement
Does it need to be kinked in the middle like it is? Could i fabricate another one that is flat?
Does anyone have the measurement for a Mag 5 one?
Cheers
Dan
Look here:
It still needs more coats to cover everything underneath where the primer got a little thin.
With the spreader arangement
Does it need to be kinked in the middle like it is? Could i fabricate another one that is flat?
Does anyone have the measurement for a Mag 5 one?
Cheers
Dan
Re: Magnum 8 on ebay
Hello Dan did you get my email with the pictures
Cheers Stuart
Cheers Stuart
Decending into insanity or is it an addiction
Int moth
Magnum 8 k3920
Mystery skoll
Skoll and crossbones
Shelly mk2 2825
Int moth
Magnum 8 k3920
Mystery skoll
Skoll and crossbones
Shelly mk2 2825
Re: Magnum 8 on ebay
Hi Stuart
Yeah I got the photos you sent through. Do you happen to have any measurements?
Cheers
Dan
Yeah I got the photos you sent through. Do you happen to have any measurements?
Cheers
Dan
Re: Magnum 8 on ebay
Hello Dan not had time tonight but will measure up and do a quick sketch with measurements tomorrow and mail it to you
Cheers Stuart
Cheers Stuart
Decending into insanity or is it an addiction
Int moth
Magnum 8 k3920
Mystery skoll
Skoll and crossbones
Shelly mk2 2825
Int moth
Magnum 8 k3920
Mystery skoll
Skoll and crossbones
Shelly mk2 2825
Re: Magnum 8 on ebay
Admin edit: moved this thread as it's no longer relevant to the for sale section
-
- Posts: 41
- Joined: Fri Aug 10, 2012 12:40 pm
- Location: york
Re: Magnum 8 on ebay
this is looking good, i'll try and take some photos of my magnum 8 spreader arrangement and some dimensions.
Scorpion 1925
International moth magnum 8
Ford Capri
International moth magnum 8
Ford Capri
Re: Magnum 8 on ebay
I talked to a bunch of Mothies of my sort of age on this last year.hollandsd wrote: Do you happen to have any measurements?
The answer I got back was that the shrouds should be offset about an inch outwards and an inch back by the spreader, and the prod (forward arm) should be neutral on the forestay. Obviously the subtleties depend a lot on how you want your mast to bend to get your sail right, and I've found with a rig of that era (Needlespar/Sanders) on my Skol that I want loads of bend in the bottom of the mast to take out luff round, to the extent that the sort of forward facing diamond the mast has to control kicker bend should actually be slack with the kicker off.
Re: Magnum 8 on ebay
More done this weekend, i've put the first coat on the foredeck and will do one more (im not too bothered about the roughness.
See photos:
Dan
See photos:
Dan
-
- Posts: 41
- Joined: Fri Aug 10, 2012 12:40 pm
- Location: york
Re: Magnum 8 on ebay
i hope i have attached some pictures and dimensions of the one fitted to my magnum 8hollandsd wrote:I've got her back and she looks ok.
There's a weird spreader contraption on the mast that I think is designed to hold the shrouds and the forestay but currently looks broken and only holds the shrouds.
Can anyone post images of what it should really look like?
Cheers
Dan
martyn
Scorpion 1925
International moth magnum 8
Ford Capri
International moth magnum 8
Ford Capri
Re: Magnum 8 on ebay
All done and packed up ready to take to the club on Sunday.
Dont think ill be sailing her but a smaller friend of mine may be.
Just waiting for the materials to arrive for the gooseneck pin and the spreader.
Dan
Dont think ill be sailing her but a smaller friend of mine may be.
Just waiting for the materials to arrive for the gooseneck pin and the spreader.
Dan